Ross CrossOver 12 Instrukcja Obsługi Pobierz pdf (Strona 19)

•

SqzHor — Squeeze Horizontally ( )

•

SqzVert — Squeeze Vertically

(double-press )

•

SqzCtr — Squeeze to the Center ( )

•

PushUL — Push to Upper-Left ( )

•

PushUR — Push to Upper-Right

(double-press )

•

PushDL — Push to Lower-Left

(double-press )

•

PushDR — Push to Lower-Right

(double-press )

•

SqzUR — Squeeze to Upper-Right ( )

•

SqzUL — Squeeze to Upper-Left ( )

•

SqzDR — Squeeze to Lower-Right

(double-press )

•

SqzDL — Squeeze to Lower-Right

(double-press )

•

CirclL — Circle Left ( )

•

CirclR — Circle Right (double-press )

•

FlyTru — Fly Through (double-press )

•

Strtch — Stretch Horizontally to Black ( )

•

Tumble — Tumble Down (double-press )

•

1000lb — Falls and then Bounces

•

SqzU — Squeeze Up

•

SqzD — Squeeze Down

•

SqzL — Squeeze Left

•

SqzR — Squeeze Right

MediaWipe Transitions

A MediaWipe

™

allows you to use an animation to cover

a transition. When the transition starts, the switcher plays

the selected animation over top of the background and

keys that are being transitioned. When the cut point is

reached, the switcher performs a cut transition.

It is important to use a full-screen image in the animation

at the cut point so that the cut is not visible on-air.

Keep the following in mind when performing

MediaWipes:

• Although you can select a still image for a media

transition, it is not recommended.

• Only Auto Transition should be used for Media

transitions. Using the fader to perform the transition

manually could result in jumps in the animation.

• The duration of the transition (Time) is set by the

length of the animation and the play speed of the

animation.

To Set Up a MediaWipe

A MediaWipe

™

requires that you select the animation

you want to use. How the animation plays and appears

during the transition is stored in the animation. Refer to

Media-Store on page 39 for information animations.

Press MEDIA.

Press NEXT.

Press the Browse knob.

Use the Browse knob select the location where

the animation is stored. You can also load an

animation by entering the media number using

the pattern buttons.

•

Internal(0) — Internal cache (ﬂash memory

containing sample images only)

•

USB(1) — USB drive installed in the frame

Press the left knob.

Use the left knob to select the animation you

want to use for the transition.

If you have not set a cut frame for the animation,

use the fader to move through the animation to

the point where you want the video behind the

animation to cut to the new video source.

Press and hold the MEDIA button and press CUT

to set the new cut frame.

Transition Limits

The Transition Limit allows you to set the point in a

transition where an auto transition stops. When active,

the point in the transition where the auto transition will

stop is indicated by a ﬂashing segment on the transition

progress bar next to the fader handle. The auto transition

proceeds to this point and stops. The second auto

transition starts from the transition limit point and either

goes back to where the ﬁrst transition started.

Tip: If you turn Limit off when the transition has stopped at the

transition limit point, the next transition starts from the transition

limit point and goes forward to complete the transition, instead

of going back to the start.

To Set Up a Transition Limit

A transition limit is set using the fader of the MLE that

you want to set up the transition limit on. The transition

limit is speciﬁc to the MLE it is set on.

Set up the transition you want to perform.

Press NEXT until Limit is shown on the menu.

Carbonite Operation Manual (v6.1) — Transitions • 19

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 51 52

Komentarze do niniejszej Instrukcji

Brak uwag

Ross CrossOver 12 Instrukcja Obsługi Strona 19

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Switche sieciowe Ross CrossOver 12